এঞ্জেল ই-ভিক্টরি ৫০/৫০ (২০১৯) ইকোড্রাইভEngel
e-victory 50/50
এঞ্জেল ই-ভিক্টরি ৫০/৫০ (২০১৯) ইকোড্রাইভ
Engel
e-victory 50/50
উৎপাদন বছর
২০১৯
অবস্থা
ব্যবহৃত
অবস্থান
Trenčianske Stankovce 

মৌলিক তথ্য
- মেশিনের নাম:
- এঞ্জেল ই-ভিক্টরি ৫০/৫০ (২০১৯) ইকোড্রাইভ
- উৎপাদক:
- Engel
- মডেল:
- e-victory 50/50
- উৎপাদন বছর:
- ২০১৯
- অবস্থা:
- প্রায় নতুন (ব্যবহৃত)
মূল্য এবং অবস্থান
- বিক্রেতার অবস্থান:
- 3011 Sedličná, 913 11 Trenčianske Stankovce, স্লোভাকিয়া

কল করুন
প্রযুক্তিগত বিবরণ
ডকুমেন্টেশন এবং সার্টিফিকেশন
ডকুমেন্টেশন / ম্যানুয়াল
আরও বিস্তারিত
ক্ল্যাম্পিং ফোর্স:
৫০০ কিলো নিউটন
প্রস্তাবের বিবরণ
- বিজ্ঞাপন আইডি:
- A22892835
- রেফারেন্স নম্বর:
- 260289
- আপডেট:
- সর্বশেষ ১৬.১১.২০২৬
বিবরণ
_ENGEL – Injection Moulding Machine Technical Data_
Serial number: 232665
Model: E‑VICTORY
_Plasticising Unit 1_
• Screw diameter: 18 mm
• Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed
• Screw stroke: 80 mm
• Maximum injection volume: 20 cm³
• Screw speed: 450 rpm
• Screw torque: 75 Nm
• Plasticising rate, 3-zone screw: 4.2 g/s
_Injection Unit 1_
• Version: Standard
• Injection rate: 83.97 cm³/s
• Specific injection pressure, regenerative mode: 2,400 bar
_Nozzle 1_
• Nozzle stroke: 210 mm
• Nozzle contact force: 40.6 kN
_Material Cylinder 1_
• Screw L/D ratio: 24
• Heating zones, including nozzle: 4
• Heating power: 5.1 kW
• Note: maximum available equipment
_Clamping Unit_
• Clamping force: 500 kN (approximately 50 tonnes)
• Opening stroke + cylinder tolerance: 408 mm
• Maximum distance between platens: 600 mm
• Minimum mould height: 200 mm
• Platen dimensions, horizontal × vertical: 500 × 450 mm
• Drop-out chute width: 400 mm
• Maximum mould weight on moving platen: 300 kg
• Maximum mould weight on stationary platen: 300 kg
• Maximum total mould weight: 600 kg
• Dry-cycle stroke according to Euromap 6: 150 mm
• Dry-cycle time according to Euromap 6: 1.60 s
Mould weight notes:
1. Mould overhang according to mounting platens.
2. Less the weight of any rotary table.
Knjdpfx Asz Iyldeared
_Ejector 1_
• Ejector stroke: 100 mm
• Ejector force: 39.8 kN
_Drive Unit_
• Oil reservoir capacity – injection unit, main tank: 135 l
• Oil reservoir capacity – clamping unit, auxiliary tank: 0 l
_Machine Basics_
• Total weight without oil: 4.0 tonnes
• Total connected power: 65.0 kW
Transcription note: the small footnotes below the plasticising section specify
reference materials and test conditions. They are not fully legible in this
photo.
Serial number: 232665
Model: E‑VICTORY
_Plasticising Unit 1_
• Screw diameter: 18 mm
• Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed
• Screw stroke: 80 mm
• Maximum injection volume: 20 cm³
• Screw speed: 450 rpm
• Screw torque: 75 Nm
• Plasticising rate, 3-zone screw: 4.2 g/s
_Injection Unit 1_
• Version: Standard
• Injection rate: 83.97 cm³/s
• Specific injection pressure, regenerative mode: 2,400 bar
_Nozzle 1_
• Nozzle stroke: 210 mm
• Nozzle contact force: 40.6 kN
_Material Cylinder 1_
• Screw L/D ratio: 24
• Heating zones, including nozzle: 4
• Heating power: 5.1 kW
• Note: maximum available equipment
_Clamping Unit_
• Clamping force: 500 kN (approximately 50 tonnes)
• Opening stroke + cylinder tolerance: 408 mm
• Maximum distance between platens: 600 mm
• Minimum mould height: 200 mm
• Platen dimensions, horizontal × vertical: 500 × 450 mm
• Drop-out chute width: 400 mm
• Maximum mould weight on moving platen: 300 kg
• Maximum mould weight on stationary platen: 300 kg
• Maximum total mould weight: 600 kg
• Dry-cycle stroke according to Euromap 6: 150 mm
• Dry-cycle time according to Euromap 6: 1.60 s
Mould weight notes:
1. Mould overhang according to mounting platens.
2. Less the weight of any rotary table.
Knjdpfx Asz Iyldeared
_Ejector 1_
• Ejector stroke: 100 mm
• Ejector force: 39.8 kN
_Drive Unit_
• Oil reservoir capacity – injection unit, main tank: 135 l
• Oil reservoir capacity – clamping unit, auxiliary tank: 0 l
_Machine Basics_
• Total weight without oil: 4.0 tonnes
• Total connected power: 65.0 kW
Transcription note: the small footnotes below the plasticising section specify
reference materials and test conditions. They are not fully legible in this
photo.
এই বিজ্ঞাপনগুলি আপনারও আগ্রহের হতে পারে।
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Trenčianske Stankovce
৬,৭৮৮ km
Engel E-VICTORY 170H/50V/120 কম্বি (২০১৫) ইকোড্রাইভ, VIPER 20 লিনিয়ার রোবট
EngelE-Victory 170H/50V/120 combi
EngelE-Victory 170H/50V/120 combi
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Juszczyn
৬,৬৫৯ km
ছাঁচনির্মাণ
WeinigProfimat 23 Fortec
WeinigProfimat 23 Fortec
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
রোমানিয়া
৭,৫২০ km
Engel DUO 7050/650 পিকো
EngelDUO 7050/650 pico
EngelDUO 7050/650 pico
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Düngenheim
৭,৫৪৪ km
বৈদ্যুতিক তারের দড়ি উত্তোলন 3.2t, নতুন স্টকে আছে
Abus KransystemeGM800.3200 H-202.41.6000.4E 100.20
Abus KransystemeGM800.3200 H-202.41.6000.4E 100.20
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Schlüchtern
৭,৩৭৫ km
টুল রুম MILLING মেশিন
HermleUWF 802 M
HermleUWF 802 M
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Eisingen
৭,৪৬৪ km
ইনজেকশন ছাঁচনির্মাণ মেশিন
ENGELe-motion 310/160T
ENGELe-motion 310/160T
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Wilków
৬,৭৯৯ km
স্ক্রু কম্প্রেসার
KaeserASD 47 SFC
KaeserASD 47 SFC
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Burgoberbach
৭,৩২১ km
পেরিফেরাল ডিভাইস
Wanner TechnikC17.31sv
Wanner TechnikC17.31sv
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Скопје
৬,৫৭৫ km
ইনজেকশন মোল্ডিং মেশিন
BATTENFELDPLUS 35-INJECTION MOLDING MACHINE
BATTENFELDPLUS 35-INJECTION MOLDING MACHINE
সফল
আপনার বার্তাটি পাঠানো হয়েছে।
ক্ষুদ্র বিজ্ঞাপন
Sheffield
৮,০৪০ km
3D প্রিন্টার
ProJetSD6000
ProJetSD6000
আপনার বিজ্ঞাপন সফলভাবে মুছে ফেলা হয়েছে
একটি ত্রুটি ঘটেছে




























































































































































