গরম: +৫০°C / +২০০°C ঠান্ডা: -৮০°C / +১০০°C

CTS Temperaturschock-Prüfschrank TSS-70/130 130 Liter

CTS
Type: TSS-70/130
Water-cooled refrigeration unit
For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130.
This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance.

Application Areas:
- Material testing
- Aging tests
- Electronics and component testing
- Thermal shock and temperature cycling tests

Technical Specifications:

Type: TSS-70/130
Test volume: 130 liters
Temperature range:
- Hot chamber: +50°C to +200°C
- Cold chamber: -80°C to +100°C
Heating rate: approx. 6 K/min from ambient temperature to +180°C
Cooling rate: approx. 4 K/min from ambient temperature to -60°C
Temperature deviation:
- ±1 K over time
- ±2 K spatially
Temperature change rate:
- max. 100 K/min average for shock test mode (no radiant heat)
Transfer time between chambers:
- ≤ 15 min for -65°C to +200°C with 10 kg ICs
Changeover time:
- < 10 seconds

Electrical Specifications:
Connection: 400 V, 3/N, 50 Hz
Nominal power: approx. 17.2 kW
Nominal current: approx. 29 A
Site fuse: 32 A slow-blow
Connection: Cekon 32

Refrigeration System:
Refrigerant: R404A / R23
Water-cooled, low noise, fully hermetic

Features/Equipment:
- CTS control panel
- Microprocessor-controlled regulation and monitoring system
- Programmable operation (up to 100 test programs)
- Digital setpoint and actual value display
- RS232 interface
- 2 free switching channels for external device control
- Fault notification via volt-free contact
(Loadable up to 30 V DC, 2 A)
- EMC tested

Technical Construction:
- Hot and cold chambers
- Transfer basket with spindle drive
- Test chamber/transfer basket made of stainless steel (material no. 1.4301)
- Stainless steel wire insert basket
- Tube port NW 50 with sealing plug
- Compressed air connection 1/4" male
- Non-pressurized condensate drain R 1/2" female thread
- Safety door locking
- Lockable door with window

Dimensions (according to installation diagram):
External dimensions approx.: 2335 x 940 x 1820 mm
Installation clearance approx.: 1990 x 940 x 1652 mm
Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm
Window: 300 x 300 mm

Additional Data:
Protection class: IP 22
Sound pressure level: < 60 dB(A)
Weight: approx. 950 kg
Average consumption during test cycle: approx. 8 kWh

Important information for your safety as a buyer!
The following points are performed on our offered chambers in advance:
1. Functional check and replacement of necessary components
2. If required, refill with legally compliant refrigerant
3. Leak test with certificate
4. After successful inspection, chambers undergo a documented test run.

Condition: used
Scope of delivery: see photos
(Specifications subject to change and errors excepted.)
For further questions, please feel free to contact us by phone.
Ppjdpoy Hkd Hofx An Nor

বিজ্ঞাপনটি স্বয়ংক্রিয়ভাবে অনুবাদ করা হয়েছে। অনুবাদে ত্রুটি থাকতে পারে।